Main range of productModicon OTB product or component typeI/O distributed module integrated connection typeNon isolated serial link 2 x RJ45 in parallel, master/slave Modbus, RTU/ASCII, transmission mode: asynchronous in baseband, RS485, transmission mode: 2 twisted shielded pairs at 1.2...38.4 kbit/s half duplex discrete input number12 conforming to EN/IEC 61131 type 1 discrete input logicSink or source discrete input current5 mA for I0...I15 mA for I6...I77 mA for I2...I57 mA for I8...I11 discrete output number2 solid state PNP for Q0...Q1 output logic: source6 relay for Q2...Q7 discrete output current2000 mA relay300 mA solid state Complementary topologyDevices linked by daisy-chaining or tap junctions bus length0...10 m tap-off length: 0...15 m number of devices per segment0...32 data format7 or 8 bits, 1 or 2 stop bits parityEvenNoOdd discrete input voltage24 V discrete input voltage typeDC discrete input typeNPN or PNP input voltage limits20.4...26.4 V electronic filtering time0.035 ms for I0...I1 at state 10.035 ms for I6...I7 at state 10.04 ms for I2...I5 at state 10.04 ms for I8...I11 at state 10.045 ms for I0...I1 at state 00.045 ms for I6...I7 at state 00.15 ms for I2...I5 at state 00.15 ms for I8...I11 at state 0 configurable filtering time0 ms12 ms3 ms input impedance3.4 kOhm for I2...I53.4 kOhm for I8...I115.7 kOhm for I0...I15.7 kOhm for I6...I7 discrete output voltage24 V DC solid state240 V AC relay30 V DC relay output voltage limits20.4...28.8 V solid state maximum output current360 mA solid state current per output common8 A relay<= 0.72 A solid state current consumption30 mA at 5 V DC (at state 1) relay output40 mA at 24 V DC (at state 1) relay output5 mA at 5 V DC (at state 0) relay output output overvoltage protection38...40 V tungsten load8 W for solid state response time300 µs at state 0 for relay300 µs at state 1 for relay5 µs at state 0 for solid state5 µs at state 1 for solid state switchable load>= 0.1 mA contact bounce time<= 1 ms for relay leakage current<= 0.1 mA at state 0 for solid state drop-out voltage<= 1 V at state 1 insulation between channel and internal logic1500 Vrms for 1 minute for relay output500 Vrms for 1 minute for input circuit500 Vrms for 1 minute for solid state output insulation between channelsNone contact resistance<= 30 mOhm electrical durability500000 cycles AC-1 with 500 VA load for relay output500000 cycles AC-14 with 250 VA load for relay output500000 cycles AC-15 with 200 VA load for relay output500000 cycles DC-1 with 60 W load for relay output500000 cycles DC-13 with 30 W load for relay output supply circuit typeDC [Us] rated supply voltage24 V supply voltage limits20.4...26.2 V input current<= 700 mA at 26.2 V for supply circuit inrush current<= 1 A for solid state output<= 50 A for supply circuit power consumption in W19 W number of I/O expansion module7 I/O expansion capacity132 with screw terminal discrete I/O module(s)188 with spring terminal discrete I/O module(s)244 with HE10 connector discrete I/O module(s)7 x 8I or 7 x 2I or 7 x (4I/2O) with screw terminal analogue I/O module(s) insulation resistance>= 10 mOhm between I/O and earth terminals>= 10 mOhm between power supply and earth I/O connectionRemovable screw terminal block number of common point1 for relay output (1 NO)1 for relay output (2 NO)1 for relay output (3 NO)1 for input1 for solid state output counting input number2 counting capacity32 bits counting frequency20000 Hz5000 Hz pulse generator number2 pulse generator frequency7 kHz pulse generator functionRPLS pulse generator outputRPWM pulse width modulation markingCE fixing modeBy clips on 35 mm symmetrical DIN railBy screws on panel with fixing kitBy screws on solid plate with fixing kit status LED1 LED per channel, green for I/O1 LED, green for PWR1 LED, red for ERR1 LED, yellow for COM product weight0.19 kg Environment IP degree of protectionIP20 immunity to microbreaks10 ms for supply circuit dielectric strength500 V between I/O and earth terminals500 V between power supply and earth standardsCSAEN 61131-2IEC 61131-2UL 508CSA C22.2 No 213 Class I Division 2 Group ACSA C22.2 No 213 Class I Division 2 Group BCSA C22.2 No 213 Class I Division 2 Group CCSA C22.2 No 213 Class I Division 2 Group D product certificationscULus ambient air temperature for operation0...55 °C ambient air temperature for storage-25...70 °C relative humidity30...95 % without condensation pollution degree2 conforming to EN 606642 conforming to IEC 60664 operating altitude0...2000 m storage altitude0...3000 m vibration resistance0.075 mm (f = 10...57 Hz) on 35 mm symmetrical DIN rail1 gn (f = 57...150 Hz) on 35 mm symmetrical DIN rail shock resistance15 gn for 11 ms conforming to EN 6113115 gn for 11 ms conforming to IEC 61131 resistance to electrostatic discharge4 kV in contact conforming to IEC 61000-4-28 kV in air conforming to EN 61000-4-24 kV in contact conforming to EN 61000-4-28 kV in air conforming to IEC 61000-4-2 resistance to radiated fields10 V/m, 80000000...2000000000 Hz conforming to EN 61000-4-310 V/m, 80000000...2000000000 Hz conforming to IEC 61000-4-3 resistance to fast transients1 kV for 24 V solid state I/O conforming to IEC 61000-4-42 kV for 24 V supply conforming to IEC 61000-4-4 Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
CatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsOTB Guide de mise à jour du logiciel embarqué dans les modules OTB (Version 1)CADSizeAdd to My DocumentsCAD file (on TraceParts) for OTB1S0DM9LP: I/O distributed module OTB - Modbus non isolated serial link - 0..10 m (Version 2.0)Instruction sheetSizeAdd to My DocumentsDeclaration of conformitySizeAdd to My DocumentsEnd of Life InformationSizeAdd to My Documents
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.