ATV71EXC2C11N4H

Altivar 71 Plus-LH

Variable speed drive

ATV71

Asynchronous motors
Synchronous motors

In floor-standing enclosure compact version

A line choke
A switch and fast-acting fuses
An IP65 remote mounting kit for graphic display terminal
Terminals/bars for motor connection
A wired ready-assembled Schneider Spacial SF enclosure
Active infeed converter
Control transformer 230 V AC
Power supply 24 V DC
Clean power filter with integrated EMC filter
ATV71HC11N4 standard drive IP00

Integrated

3 phases

380...415 V (+/- 10 %)

342...457 V

50...60 Hz (+/- 5 %)

47.5...63 Hz

110 kW 3 phases at 380...415 V

177 A at 400 V 3 phases 110 kW

123 kVA at 400 V 3 phases 110 kW

100 kA with external fuses
100 kA with option circuit breaker

215 A 2.5 kHz at 400 V 3 phases

323 A for 60 s at 400 V 3 phases

0.1...500 Hz

2.5 kHz

2...8 kHz adjustable
2.5...8 kHz with derating factor

1...100 in open-loop mode, without speed feedback

+/- 0.01 % of nominal speed (0.2 Tn to Tn) in closed-loop mode with encoder feedback
+/- 10 % of nominal slip (0.2 Tn to Tn) without speed feedback

+/- 15 % in open-loop mode, without speed feedback
+/- 5 % in closed-loop mode with encoder feedback

170 % of nominal motor torque (+/- 10 %) 60 s
220 % of nominal motor torque (+/- 10 %) 2 s

100 % continuous
120 % for 60 seconds

ENA (Energy adaptation) system for unbalanced loads
Voltage/frequency ratio (2 or 5 points)
Vector control with/without speed feedback

Vector control without sensor, standard
Vector control with sensor, standard

Adjustable PI regulator

Adjustable
Automatic whatever the load
Can be suppressed
Not available in voltage/frequency ratio (2 or 5 points)

Class 3 conforming to EN 50178

LCD display unit with operation function, status and configuration - mounted in the front door

<= power supply voltage

Between power and control terminals

IEC cable at 40 °C copper 70 °C PVC

Terminal, clamping capacity: 2.5 mm² AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR) for entry from the bottom
Terminal M10, clamping capacity: 2 x 150 mm² (L1/R, L2/S, L3/T) for entry from the bottom
Terminal M12, clamping capacity: 2 x 240 mm² (U/T1, V/T2, W/T3) for entry from the bottom

3 x 120 mm²

250 A for fuse 3 gI power supply upstream

External supply at 24 V DC 19...30 V 1 A 30 W
Internal supply for reference potentiometer at 10 V DC 10...11 V <= 10 mA
Internal supply at 24 V DC 21...27 V <= 100 mA

2

Bipolar differential voltage (AI1-/Al1+) +/- 10 V DC at 24 V max, duration: 1.5...2.5 ms) 11 bits + sign
Software-configurable voltage (AI2) 0...10 V DC at 24 V max 30 kOhm, duration: 1.5...2.5 ms) 11 bits
Software-configurable current (AI2) 0...20 mA/4...20 mA 250 Ohm, duration: 1.5...2.5 ms) 11 bits

1

Software-configurable voltage (AO1) 0...10 V DC at 470 Ohm, duration: 1.5...2.5 ms 10 bits
Software-configurable current (AO1) 0...20 mA/4...20 mA at 500 Ohm, duration: 1.5...2.5 ms 10 bits

1

Configurable relay logic (R1A, R1B, R1C) NO/NC, response time: 6.5...7.5 ms - electrical durability: 100000 cycles

3 mA at 24 V DC (configurable relay logic)

5 A at 250 V AC - load type: resistive cos phi = 1 configurable relay logic
5 A at 30 V DC - load type: resistive L/R = 0 ms configurable relay logic
2 A at 250 V AC - load type: inductive cos phi = 0.4 configurable relay logic
2 A at 30 V DC - load type: inductive L/R = 7 ms configurable relay logic

6

Programmable (LI1...LI4) at 24 V DC <= 30 V level 1 PLC 3.5 kOhm (duration=1.5...2.5 ms)
Switch-configurable (LI6) at 24 V DC <= 30 V level 1 PLC 1.5 kOhm (duration=1.5...2.5 ms)
Safety input (PWR) at 24 V DC <= 30 V 1.5 kOhm

Positive logic (source) (LI1...LI6) voltage (state 0): 0...5 V voltage (state 1): 11...30 V
Negative logic (sink) (LI1...LI6) voltage (state 0): 16...30 V voltage (state 1): 0...10 V
Positive logic (source) (PWR) voltage (state 0): 0...2 V voltage (state 1): 17...30 V

Linear adjustable separately from 0.01 to 9000 s
S, U or customized

By regenerative braking with active front end

Overheating protection for drive
Short-circuit between motor phases for drive
Overcurrent between output phases and earth for drive
Overvoltages on the DC bus for drive
Against exceeding limit speed for drive
Line supply undervoltage for drive
Line supply overvoltage for drive
Against input phase loss for drive
Thermal protection for motor
Motor phase break for motor
Power removal for drive

3535 V DC between earth and power terminals
5092 V DC between control and power terminals

> 1 mOhm at 500 V DC for 1 minute to earth

0.1 Hz for display unit
0.024/50 Hz for analog input

CANopen
Modbus

1 RJ45 - communication protocol: Modbus on front face
1 RJ45 - communication protocol: Modbus on terminal
Male SUB-D 9 on RJ45 - communication protocol: CANopen

2-wire RS 485 - communication protocol: Modbus

RTU - communication protocol: Modbus

20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps - communication protocol: CANopen
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps - communication protocol: Modbus on terminal
9600 bps, 19200 bps - communication protocol: Modbus on front face

8 bits, 1 stop, even parity - communication protocol: Modbus on front face
8 bits, odd even or no configurable parity - communication protocol: Modbus on terminal

No impedance - communication protocol: Modbus

1...127 - communication protocol: CANopen
1...247 - communication protocol: Modbus

Slave - communication protocol: CANopen

Safe standstill for power circuit
PTC relay for power circuit
Pt100 relay for power circuit
Insulation monitoring for power circuit
Design for IT networks for power circuit
External 230 V supply terminals for power circuit
Buffer voltage 24 V DC power supply for power circuit
Enclosure lighting for power circuit
Key switch (local/remote) for power circuit
Motor heating for power circuit
External motor fan for power circuit
Voltmeter for power circuit
Door handle for main switch for power circuit
Ammeter for power circuit
Enclosure heating for power circuit
Motor choke for power circuit
Cable entry via the top for power circuit
Enclosure plinth for power circuit
Relay output C/O for control circuit
External 24 V DC supply terminals for power circuit
Control terminals for control circuit
Adaptor for 115 V logic inputs for control circuit
Isolated amplifier for control circuit

Communication card - communication protocol: CC-Link
Communication card - communication protocol: DeviceNet
Communication card - communication protocol: Ethernet/IP
Communication card - communication protocol: Fipio
Communication card - communication protocol: Interbus-S
Communication card - communication protocol: Modbus Plus
Communication card - communication protocol: Modbus TCP
Communication card - communication protocol: Modbus/Uni-Telway
Communication card - communication protocol: Profibus DP
Communication card - communication protocol: Profibus DP V1
Controller inside programmable card
Basic I/O extension card
Extended I/O extension card
Encoder interface cards

Vertical +/- 10 degree

Light grey RAL 7035

800 mm

2157 mm

642 mm

605 kg

IP23

EN 60204-1
EN 61800-3 environments 2 category C3
EN 61800-5-1
EN 61800-2

ATEX
C-Tick
GOST

CE

69 dB

2 conforming to EN/IEC 61800-5-1

0.6 gn (f=10...200 Hz) conforming to EN/IEC 60068-2-6
1.5 mm peak to peak (f=3...10 Hz) conforming to EN/IEC 60068-2-6
3M3 conforming to EN/IEC 60721-3-3

4 gn 11 ms conforming to EN/IEC 60068-2-27
3M2 conforming to EN/IEC 60721-3-3

3K3 without condensation conforming to IEC 60721-3-3

0...95 %

0...40 °C without derating
40...50 °C with current derating of 1.8 % per °C

-25...70 °C

1200 m3/h

<= 1000 m without derating
1000...3000 m with current derating 1 % per 100 m