enclosed variable speed drive ATV71 Plus - 315 kW - 400V - IP54 - ready to useShow more characteristics >
- Reason for Substitution: End of life
- Substitution date: 01 April 2016
Main range of productAltivar 71 Plus product or component typeVariable speed drive device short nameATV71 Plus product destinationAsynchronous motorsSynchronous motors product specific applicationComplex, high-power machines assembly styleIn floor-standing enclosure with separate air flowsReady to use product compositionA DC chokeA plinthAn IP65 remote mounting kit for graphic display terminalMotor terminalsA wired ready-assembled Sarel Spacial 6000 enclosureCircuit breakerATV71HC31N4 drive on heatsink EMC filterIntegrated network number of phases3 phases rated supply voltage380...415 V (+/- 10 %) supply voltage limits342...457 V supply frequency50...60 Hz (+/- 5 %) network frequency47.5...63 Hz motor power kW315 kW for 380...415 V line current529 A for 400 V / 315 kW Complementary apparent power365 kVA for 400 V / 315 kW prospective line Isc<= 50 kA with external fuses continuous output current616 A at 2.5 kHz, 400 V / 315 kW maximum transient current924 A for 60 s / 315 kW / 500 hp1016 A for 2 s / 315 kW / 500 hp speed drive output frequency0.1...500 Hz nominal switching frequency2.5 kHz switching frequency2...8 kHz adjustable2.5...8 kHz with derating factor speed range1...100 asynchronous motor in open-loop mode, without speed feedback1...50 synchronous motor in open-loop mode, without speed feedback1...1000 asynchronous motor in closed-loop mode with encoder feedback speed accuracy+/- 0.01 % of nominal speed for 0.2 Tn to Tn torque variation, in closed-loop mode with encoder feedback+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation, without speed feedback torque accuracy+/- 15 % in open-loop mode, without speed feedback+/- 5 % in closed-loop mode with encoder feedback transient overtorque170 % of nominal motor torque, +/- 10 % for 60 s220 % of nominal motor torque, +/- 10 % for 2 s braking torque<= 150 % with braking or hoist resistor30 % without braking resistor asynchronous motor control profileVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standardVoltage/frequency ratio - Energy Saving, quadratic U/fFlux vector control without sensor, ENA (energy Adaptation) systemFlux vector control without sensor, 2 pointsFlux vector control with sensor, standard synchronous motor control profileVector control without sensor, standardVector control with sensor, standard regulation loopAdjustable PI regulator motor slip compensationAdjustableAutomatic whatever the loadNot available in voltage/frequency ratio (2 or 5 points)Suppressable overvoltage categoryClass 3 conforming to EN 50178 local signallingLCD display unit - operation function, status and configuration output voltage<= supply voltage isolationElectrical between power and control type of cable for external connectionIEC cable - 40 °C, copper 70 °C / PVCUL 508 cable - 40 °C, copper 75 °C / PVC electrical connectionBar M12 - 4 x 300 mm² (L1/R, L2/S, L3/T) bottom entryBar M12 - 4 x 240 mm² (U/T1, V/T2, W/T3) bottom entryTerminal - 2.5 mm² / AWG 14 (R1A, R1B, R1C, R2A, R2B) bottom entryScrew clamp terminals - 1.5 mm² (AI1-/AI1+, AI2, AO1, LI1...LI6, PWR) bottom entry motor recommanded cable cross section3 (3 x 150) mm² short-circuit protection800 A fuse protection type gI - power supply upstream supplyExternal supply : 24 V DC (19...30 V) - 1 AInternal supply for reference potentiometer : 10 V DC (10...11 V) - <= 10 mAInternal supply : 24 V DC (21...27 V) - <= 100 mA analogue input number2 analogue input typeSoftware-configurable current : (AI2) 0...20 mA/4...20 mA - 250 Ohm - sampling time: 1.5...2.5 ms - resolution: 11 bitsBipolar differential voltage : (AI1-/Al1+) +/- 10 V DC - 24 V max - sampling time: 1.5...2.5 ms - resolution: 11 bits + signSoftware-configurable voltage : (AI2) 0...10 V DC - 24 V max - 30000 Ohm - sampling time: 1.5...2.5 ms - resolution: 11 bits analogue output number1 analogue output typeSoftware-configurable voltage : (AO1) 0...10 V DC - 470 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bitsSoftware-configurable current : (AO1) 0...20 mA/4...20 mA - 500 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bits discrete output number2 discrete output typeConfigurable relay logic : (R1A, R1B, R1C) NO/NC - 6.5...7.5 ms - 100000 cyclesConfigurable relay logic : (R2A, R2B) NO - 6.5...7.5 ms - 100000 cycles minimum switching current3 mA at 24 V DC (configurable relay logic) maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 (R1, R2)5 A at 30 V DC on resistive load - L/R = 0 ms (R1, R2)2 A at 250 V AC on inductive load - cos phi = 0.4 (R1, R2)2 A at 30 V DC on inductive load - L/R = 7 ms (R1, R2) discrete input number7 discrete input typeProgrammable (LI1...LI5) 24 V DC (<= 30 V) , with level 1 PLC - 3.5 kOhm - sampling time: 1.5...2.5 msSwitch-configurable (LI6) 24 V DC (<= 30 V) , with level 1 PLC - 1.5 kOhm - sampling time: 1.5...2.5 msSafety input (PWR) 24 V DC (<= 30 V) - 1.5 kOhm discrete input logicPositive logic (source) (LI1...LI6) , 0...5 V (state 0), 11...30 V (state 1)Negative logic (sink) (LI1...LI6) , 16...30 V (state 0), 0...10 V (state 1)Positive logic (source) (PWR) , 0...2 V (state 0), 17...30 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 sS, U or customized braking to standstillBy DC injection protection typeOverheating protection for driveThermal protection for driveShort-circuit between motor phases for driveOvercurrent between output phases and earth for driveOvervoltages on the DC bus for driveBreak on the control circuit for driveAgainst exceeding limit speed for driveLine supply undervoltage for driveLine supply overvoltage for driveAgainst input phase loss for driveThermal protection for motorMotor phase break for motorInput phase breaks for drivePower removal for motor dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance> 1 mOhm at 500 V DC for 1 minute to earth frequency resolution0.1 Hz for display unit0.024/50 Hz for analog input communication port protocolCANopenModbus connector type1 RJ45 for Modbus on front face1 RJ45 for Modbus on terminalMale SUB-D 9 on RJ45 for CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal9600 bps, 19200 bps for Modbus on front face data format8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal type of polarizationNo impedance for Modbus number of addresses1...247 addresses for Modbus1...127 addresses for CANopen method of accessSlave for CANopen operating positionVertical +/- 10 degree colour of enclosureLight grey RAL 7035 colour of base of enclosureDark grey RAL 7022 height2362 mm width1400 mm depth642 mm product weight745 kg Environment electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Voltage dips and interruptions immunity test conforming to IEC 61000-4-11Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6 pollution degree2 conforming to EN/IEC 61800-5-1 IP degree of protectionIP54 vibration resistance3M3 conforming to EN/IEC 60721-3-31.5 mm peak to peak (f = 3...10 Hz) conforming to EN/IEC 60068-2-60.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-6 shock resistance3M2 conforming to EN/IEC 60721-3-34 gn for 11 ms conforming to EN/IEC 60068-2-27 noise level73 dB conforming to 86/188/EEC environmental characteristic3C2 without condensation conforming to IEC 60721-3-33K3 without condensation conforming to IEC 60721-3-33S2 without condensation conforming to IEC 60721-3-3 relative humidity0...95 % ambient air temperature for operation0...40 °C without derating40...50 °C with current derating of 1.2 % per °C ambient air temperature for storage-25...70 °C volume of cooling air2200 m3/h operating altitude<= 1000 m without derating1000...3000 m with current derating 1 % per 100 m standardsEN 55011 class A group 2EN 61800-3 environments 1 category C3EN 61800-3 environments 2 category C3EN/IEC 61800-3EN/IEC 61800-5-1 product certificationsATEXGOST markingCE Offer Sustainability RoHS (date code: YYWW) Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
CatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsDTM filesSizeAdd to My Documents
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Dimensions DrawingsReady to Use IP 54 EnclosureDimensions
NOTE: For each floor-standing enclosure added, allow a 4 mm/0.15 in. space for the seal.
Connections and SchemaReady to Use IP 54 EnclosureWiring DiagramA1DriveA2EnclosureL1DC chokeMMotorQ1Circuit breaker(1)Filter(2)Control(3)Relay control(4)Reference potentiometer(5)PLC
Performance CurvesReady to Use IP 54 EnclosureDerating Curves
The derating curves for the drive nominal current (In) are dependent on the temperature and switching frequency. For intermediate temperatures, interpolate between 2 curves.
NOTE: The drive will reduce the switching frequency automatically in the event of excessive temperature rise.XSwitching frequency (kHz)
NOTE: The temperatures shown correspond to the temperature of the air entering the enclosure.