Main range of productAltivar 61 Plus-LH product or component typeVariable speed drive device short nameATV61 product destinationAsynchronous motorsSynchronous motors assembly styleIn floor-standing enclosure compact version kit compositionClean power filter with integrated EMC filterControl transformer 230 V ACActive infeed converterA wired ready-assembled Schneider Spacial SF enclosureATV61HC11N4D standard drive IP00Power supply 24 V DCA switch and fast-acting fusesA line chokeAn IP65 remote mounting kit for graphic display terminalTerminals/bars for motor connection EMC filterIntegrated network number of phases3 phases rated supply voltage380...415 V (+/- 10 %) supply voltage limits342...457 V supply frequency50...60 Hz (- 5...5 %) network frequency limits47.5...63 Hz motor power kW110 kW, 3 phases at 380...415 V line current177 A at 400 V 3 phases / 110 kW IP degree of protectionIP54 Complementary apparent power123 kVA at 400 V, 3 phases 110 kW prospective line Isc100 kA with external fuses100 kA with option circuit breaker8.5 kA without external fuses continuous output current215 A, 2.5 kHz at 400 V 3 phases maximum transient current258 A (duration=60 s) at 400 V 3 phases speed drive output frequency0.1...500 Hz nominal switching frequency2.5 kHz switching frequency2...8 kHz adjustable2.5...8 kHz with derating factor speed range1...100 in open-loop mode, without speed feedback speed accuracy+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback torque accuracy+/- 15 % in open-loop mode, without speed feedback transient overtorque120 % of nominal motor torque for 60 s braking torque100 % continuous120 % for 60 seconds asynchronous motor control profileFlux vector control without sensor, standardVoltage/frequency ratio (2 or 5 points)Energy saving ratio synchronous motor control profileVector control without sensor, standard regulation loopAdjustable PI regulator motor slip compensationAdjustableCan be suppressedAutomatic whatever the loadNot available in voltage/frequency ratio (2 or 5 points) overvoltage categoryClass 3 conforming to EN 50178 local signallingLCD display unit - operation function, status and configuration - mounted in the front door output voltage<= power supply voltage isolationBetween power and control terminals type of cableIEC cable at 40 °C, copper 70 °C / PVC electrical connectionTerminal - screw type M12,connection capacity: 2 x 185 mm²,terminal(s): L1/R, L2/S, L3/T, cable entry:entry from the bottomTerminal - screw type M10,connection capacity: 2 x 150 mm²,terminal(s): U/T1, V/T2, W/T3, cable entry:entry from the bottomTerminal,connection capacity: 2.5 mm² AWG 14,terminal(s): AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR, cable entry:entry from the bottom motor recommanded cable cross section3 x 120 mm² short-circuit protection250 A 1 fuse (gI fuse) on power supply upstream supplyInternal supply for reference potentiometer at 10 V DC (10...11 V), <= 10 mAInternal supply at 24 V DC (21...27 V), <= 100 mAExternal supply at 24 V DC (19...30 V), 1 A, 30 W analogue input number2 analogue input typeSoftware-configurable current : (AI2) 0...20 mA/4...20 mA - 250 Ohm - sampling time: 1.5...2.5 ms - resolution: 11 bitsSoftware-configurable voltage : (AI2) 0...10 V DC - 24 V max - 30 kOhm - sampling time: 1.5...2.5 ms - resolution: 11 bitsBipolar differential voltage : (AI1-/Al1+) +/- 10 V DC - 24 V max - sampling time: 1.5...2.5 ms - resolution: 11 bits + sign analogue output number1 analogue output typeSoftware-configurable voltage : (AO1) 0...10 V DC - 470 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bitsSoftware-configurable current : (AO1) 0...20 mA/4...20 mA - 500 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bits discrete output number1 discrete output typeConfigurable relay logic : (R1A, R1B, R1C) NO/NC - 6.5...7.5 ms - 100000 cycles minimum switching current3 mA at 24 V DC (configurable relay logic) maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 (configurable relay logic)2 A at 30 V DC on inductive load - L/R = 7 ms (configurable relay logic)5 A at 30 V DC on resistive load - L/R = 0 ms (configurable relay logic)2 A at 250 V AC on inductive load - cos phi = 0.4 (configurable relay logic) discrete input number6 discrete input typeSwitch-configurable (LI6) 24 V DC (<= 30 V) , with level 1 PLC - 1.5 kOhm - sampling time: 1.5...2.5 msSafety input (PWR) 24 V DC (<= 30 V) - 1.5 kOhmProgrammable (LI1...LI4) 24 V DC (<= 30 V) , with level 1 PLC - 3.5 kOhm - sampling time: 1.5...2.5 ms discrete input logicPositive logic (source) (LI1...LI6) , 0...5 V (state 0), 11...30 V (state 1)Negative logic (sink) (LI1...LI6) , 16...30 V (state 0), 0...10 V (state 1)Positive logic (source) (PWR) , 0...2 V (state 0), 17...30 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 sS, U or customized braking to standstillBy regenerative braking with active front end protection typeOverheating protection for driveShort-circuit between motor phases for driveOvercurrent between output phases and earth for driveOvervoltages on the DC bus for driveAgainst exceeding limit speed for driveLine supply undervoltage for driveLine supply overvoltage for driveAgainst input phase loss for driveThermal protection for motorMotor phase break for motorPower removal for drive dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance> 1 mOhm at 500 V DC for 1 minute to earth frequency resolution0.1 Hz for display unit0.024/50 Hz for analog input communication port protocolModbusCANopen connector type1 RJ45 for Modbus on front face1 RJ45 for Modbus on terminalMale SUB-D 9 on RJ45 for CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal9600 bps, 19200 bps for Modbus on front face data format8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal type of polarizationNo impedance for Modbus number of addresses1...247 for Modbus1...127 for CANopen method of accessSlave for CANopen function availableSafe standstill for power circuitPTC relay for power circuitPt100 relay for power circuitInsulation monitoring for power circuitDesign for IT networks for power circuitExternal 230 V supply terminals for power circuitBuffer voltage 24 V DC power supply for power circuitEnclosure lighting for power circuitKey switch (local/remote) for power circuitMotor heating for power circuitExternal motor fan for power circuitVoltmeter for power circuitDoor handle for main switch for power circuitAmmeter for power circuitEnclosure heating for power circuitMotor choke for power circuitCable entry via the top for power circuitEnclosure plinth for power circuitRelay output C/O for control circuitExternal 24 V DC supply terminals for power circuitControl terminals for control circuitAdaptor for 115 V logic inputs for control circuitIsolated amplifier for control circuit option cardController inside programmable cardMulti-pump cardCommunication card for Profibus DPBasic I/O extension cardExtended I/O extension cardEncoder interface cardsCommunication card for Modbus TCPCommunication card for FipioCommunication card for Modbus/Uni-TelwayCommunication card for Modbus PlusCommunication card for Ethernet/IPCommunication card for DeviceNetCommunication card for Profibus DP V1Communication card for Interbus-SCommunication card for CC-LinkCommunication card for LonWorksCommunication card for METASYS N2Communication card for APOGEE FLNCommunication card for BACnet operating positionVertical +/- 10 degree colour of enclosureLight grey RAL 7035 width600 mm height2237 mm depth642 mm product weight480 kg Environment standardsEN 61800-5-1EN 61800-3 environments 2 category C3EN 60204-1EN 61800-2 product certificationsATEXC-TickGOST markingCE noise level76 dB pollution degree3 conforming to EN/IEC 61800-5-1 vibration resistance3M3 conforming to EN/IEC 60721-3-31.5 mm peak to peak (f = 3...10 Hz) conforming to EN/IEC 60068-2-60.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-6 shock resistance3M2 conforming to EN/IEC 60721-3-34 gn for 11 ms conforming to EN/IEC 60068-2-27 environmental characteristic3K3 without condensation conforming to IEC 60721-3-3 relative humidity0...95 % ambient air temperature for operation0...40 °C without derating40...50 °C with current derating of 1.8 % per °C ambient air temperature for storage-25...70 °C volume of cooling air880 m3/h operating altitude<= 1000 m without derating1000...3000 m with current derating 1 % per 100 m Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Connections and SchemaWiring DiagramA1DriveA2EnclosureAICActive Infeed ConverterMMotorQ1Main switch built-in as standardQ2Optional circuit breakerF1Main fusesKM1Line contactorEMCEMC filterLFCLine Filter Choke(1)Control(2)Relay control(3)Reference potentiometer(4)Option motor choke
Performance CurvesDerating Curves
The derating curves for the drive nominal current (In) are dependent on the temperature and switching frequency. For intermediate temperatures, interpolate between 2 curves.
NOTE: The drive will reduce the switching frequency automatically in the event of excessive temperature rise.XSwitching frequency (kHz)
NOTE: The temperatures shown correspond to the temperature of the air entering the enclosure.