enclosed variable speed drive ATV61Plus - 400 kW-400V - IP54- simplified versionShow more characteristics >
Main range of productAltivar 61 Plus product or component typeVariable speed drive device short nameATV61 product destinationAsynchronous motorsSynchronous motors product specific applicationPumping and ventilation machine assembly styleIn floor-standing enclosure with separate air flowsReady to use product compositionA wired ready-assembled Sarel Spacial 6000 enclosureMotor terminalsATV61HC40N4 drive on heatsinkAn IP65 remote mounting kit for graphic display terminalA plinthA DC chokeCircuit breaker EMC filterIntegrated network number of phases3 phases rated supply voltage380...415 V (+/- 10 %) supply frequency50...60 Hz motor power kW400 kW, 3 phases at 380...415 V line current661 A 3 phases / 355 kW IP degree of protectionIP54 Complementary apparent power467 kVA for 400 V 3 phases / 355 kW prospective line Isc<= 50 kA with external fuses continuous output current759 A at 2.5 kHz, 400 V 3 phases maximum transient current911 A for 60 s, 3 phases speed drive output frequency0.1...500 Hz nominal switching frequency2.5 kHz switching frequency2...8 kHz adjustable2.5...8 kHz with derating factor speed range1...100 in open-loop mode, without speed feedback speed accuracy+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback torque accuracy+/- 15 % in open-loop mode, without speed feedback transient overtorque120 % of nominal motor torque for 60 s135 % of nominal motor torque for 2 s braking torque30 % without braking resistor<= 125 % with braking resistor asynchronous motor control profileVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standardVoltage/frequency ratio - Energy Saving, quadratic U/f synchronous motor control profileVector control without sensor, standard regulation loopAdjustable PI regulator motor slip compensationNot available in voltage/frequency ratio (2 or 5 points)Automatic whatever the loadSuppressableAdjustable supply voltage limits342...457 V network frequency limits47.5...63 Hz overvoltage categoryClass 3 EN 50178 local signallingLCD display unit - operation function, status and configuration output voltage<= supply voltage isolationElectrical between power and control type of cable for external connectionIEC cable at 40 °C, copper 70 °C / PVC electrical connectionTerminal - 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR)Bar M12 - 4 x 300 mm² (L1/R, L2/S, L3/T)Bar M12 - 4 x 240 mm² (U/T1, V/T2, W/T3) motor recommanded cable cross section3 (3 x 185) mm² short-circuit protection1000 A fuse protection (gI fuse) on power supply upstream supplyExternal supply : 24 V (19...30 V) DC, 1 AInternal supply for reference potentiometer : 10 V (10...11 V) DC, <= 10 AInternal supply : 24 V (21...27 V) DC, <= 100 A analogue input number2 analogue input typeSoftware-configurable current : (AI2) 0...20 mA/4...20 mA - 250 Ohm - sampling time: 1.5...2.5 ms - resolution: 11 bitsSoftware-configurable voltage : (AI2) 0...10 V DC - 24 V max - 30 kOhm - sampling time: 1.5...2.5 ms - resolution: 11 bitsBipolar differential voltage : (AI1-/Al1+) +/- 10 V DC - 24 V max - sampling time: 1.5...2.5 ms - resolution: 11 bits + sign analogue output number1 analogue output typeSoftware-configurable voltage : (AO1) 0...10 V DC - 470 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bitsSoftware-configurable current : (AO1) 0...20 mA/4...20 mA - 500 Ohm - sampling time: 1.5...2.5 ms - resolution: 10 bits discrete output number2 discrete output typeConfigurable relay logic : (R1A, R1B, R1C) NO/NC - 6.5...7.5 ms - 100000 cyclesConfigurable relay logic : (R2A, R2B) NO - 6.5...7.5 ms - 100000 cycles minimum switching current3 mA at 24 V DC (configurable relay logic) maximum switching current5 A at 250 V AC on resistive load - cos phi = 1 (configurable relay logic)2 A at 30 V DC on inductive load - L/R = 7 ms (configurable relay logic)5 A at 30 V DC on resistive load - L/R = 0 ms (configurable relay logic)2 A at 250 V AC on inductive load - cos phi = 0.4 (configurable relay logic) discrete input number7 discrete input typeProgrammable (LI1...LI5) 24 V DC (<= 30 V) , with level 1 PLC - 3.5 kOhm - sampling time: 1.5...2.5 msSwitch-configurable (LI6) 24 V DC (<= 30 V) , with level 1 PLC - 1.5 kOhm - sampling time: 1.5...2.5 msSafety input (PWR) 24 V DC (<= 30 V) - 1.5 kOhm discrete input logicPositive (LI1...LI6) , 0...5 V (state 0), 11...30 V (state 1)Negative (LI1...LI6) , 16...30 V (state 0), 0...10 V (state 1)Positive (PWR) , 0...2 V (state 0), 17...30 V (state 1) acceleration and deceleration rampsLinear adjustable separately from 0.01 to 9000 sS, U or customized braking to standstillBy DC injection, <= 60 s protection typeOverheating protection for driveThermal protection for driveShort-circuit between motor phases for driveOvercurrent between output phases and earth for driveOvervoltages on the DC bus for driveBreak on the control circuit for driveAgainst exceeding limit speed for driveLine supply undervoltage for driveLine supply overvoltage for driveAgainst input phase loss for driveThermal protection for motorMotor phase break for motorPower removal for driveInput phase breaks for drivePower removal for motor dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance> 1 mOhm at 500 V DC for 1 minute frequency resolution0.1 Hz for display unit0.024/50 Hz for analog input communication port protocolCANopenModbus connector type1 RJ45 for Modbus on front face1 RJ45 for Modbus on terminalMale SUB-D 9 on RJ45 for CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus transmission rate20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal9600 bps, 19200 bps for Modbus on front face data format8 bits, 1 stop, even parity for Modbus on front face8 bits, odd even or no configurable parity for Modbus on terminal type of polarizationNo impedance for Modbus number of addresses1...247 addresses for Modbus1...127 addresses for CANopen method of accessSlave for CANopen operating positionVertical +/- 10 degree colour of enclosureLight grey RAL 7035 colour of base of enclosureDark grey RAL 7022 width1400 mm height2362 mm depth642 mm product weight700 kg Environment electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3Voltage dips and interruptions immunity test conforming to IEC 61000-4-11Conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6 standardsEN 61800-3 environments 2 category C3EN/IEC 61800-3EN/IEC 61800-5-1EN 55011 class A group 2EN 61800-3 environments 1 category C3 product certificationsGOSTATEX markingCE noise level73 dB pollution degree3 conforming to EN/IEC 61800-5-1 vibration resistance3M3 conforming to EN/IEC 60721-3-30.6 gn (f = 10...200 Hz) conforming to EN/IEC 60068-2-61.5 mm (f = 3...10 Hz) conforming to EN/IEC 60068-2-6 shock resistance3M2 conforming to EN/IEC 60721-3-34 gn for 11 ms conforming to EN/IEC 60068-2-27 environmental characteristic3C2 without condensation conforming to IEC 60721-3-33K3 without condensation conforming to IEC 60721-3-33S2 without condensation conforming to IEC 60721-3-3 relative humidity0...95 % ambient air temperature for operation0...40 °C without derating40...50 °C with current derating of 2 % per °C ambient air temperature for storage-25...70 °C volume of cooling air2200 m3/h operating altitude<= 1000 m without derating1000...3000 m with current derating 1 % per 100 m Offer Sustainability RoHS (date code: YYWW) Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
Software - ReleasedSizeAdd to My DocumentsDTM filesSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsCertificateSizeAdd to My Documents
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Dimensions DrawingsReady to Use IP 54 EnclosureDimensions
NOTE: For each floor-standing enclosure added, allow a 4 mm/0.15 in. space for the seal.
Connections and SchemaReady to Use IP 54 EnclosureWiring DiagramA1DriveA2EnclosureL1DC chokeMMotorQ1Circuit breaker(1)Filter(2)Control(3)Relay control(4)Reference potentiometer(5)PLC
Performance CurvesReady to Use IP 54 EnclosureDerating Curves
The derating curves for the drive nominal current (In) are dependent on the temperature and switching frequency. For intermediate temperatures, interpolate between 2 curves.
NOTE: The drive will reduce the switching frequency automatically in the event of excessive temperature rise.XSwitching frequency (kHz)
NOTE: The temperatures shown correspond to the temperature of the air entering the enclosure.