View all Altivar 32
variable speed drive ATV32 - 1.1kW 200V - 1P - Bluetooth built-in - w heat sinkShow more characteristics
ATV32HU11M2437 has not been replaced. Please contact your customer care center for more information.
Add to My Products Remove from My Products
The maximum number of products that can be compared is 4
Main range of productAltivar 32 product or component typeVariable speed drive product destinationAsynchronous motorsSynchronous motors product specific applicationComplex machines function availableConfigure over bluetooth assembly styleWith heat sink component nameATV32 EMC filterClass C2 EMC filter integrated network number of phases1 phase [Us] rated supply voltage200...240 V - 15...10 % supply voltage limits170…264 V supply frequency50...60 Hz - 5...5 % network frequency47.5...63 Hz motor power kW1.1 kW at 200...240 V motor power hp1.5 hp at 200...240 V Complementary line current11.5 A for 240 V 1 phase 1.1 kW / 1.5 hp13.6 A for 200 V 1 phase 1.1 kW / 1.5 hp apparent power2.8 kVA at 240 V 1 phase 1.1 kW / 1.5 hp prospective line Isc1 kA for 1 phase nominal output current6.9 A at 4 kHz 240 V 1.1 kW / 1.5 hp maximum transient current10.4 A for 60 s 1.1 kW / 1.5 hp output frequency0.0005…0.599 kHz nominal switching frequency4 kHz switching frequency2...16 kHz adjustable speed range1…100 for asynchronous motor in open-loop mode speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn torque accuracy+/- 15 % transient overtorque170…200 % braking torque<= 170 % with braking resistor asynchronous motor control profileFlux vector control without sensor - Energy Saving, NoLoad lawVoltage/frequency ratio, 5 pointsFlux vector control without sensor, standardVoltage/frequency ratio, 2 pointsVoltage/frequency ratio - Energy Saving, quadratic U/f synchronous motor control profileVector control without sensor regulation loopAdjustable PID regulator motor slip compensationNot available in voltage/frequency ratio (2 or 5 points)Adjustable 0...300 %Automatic whatever the load local signalling1 LED red for drive voltage1 LED blue for bluetooth1 LED green for CANopen run1 LED red for CANopen error1 LED red for drive fault output voltage<= power supply voltage noise level43 dB conforming to 86/188/EEC insulationElectrical between power and control electrical connectionScrew terminal, clamping capacity: 0.5...1.5 mm², AWG 18...AWG 14 (control)Removable screw terminals, clamping capacity: 1.5...2.5 mm², AWG 14...AWG 12 (motor/braking resistor)Screw terminal, clamping capacity: 2.5...4 mm², AWG 12...AWG 10 (power supply) tightening torque0.5 N.m, 4.4 lb/ft (control)0.7 N.m, 7.1 lb/ft (motor/braking resistor)0.6 N.m, 5.3 lb/ft (power supply) supplyInternal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 mA, protection type: overload and short-circuit protection analogue input number3 analogue input typeAI1 voltage: 0...10 V DC, impedance: 30000 Ohm, resolution 10 bitsAI2 bipolar differential voltage: +/- 10 V DC, impedance: 30000 Ohm, resolution 10 bitsAI3 current: 0...20 mA (or 4-20 mA, x-20 mA, 20-x mA or other patterns by configuration), impedance: 250 Ohm, resolution 10 bits sampling duration2 ms (AI1, AI2, AI3) - analog input(s)2 ms (AO1) - analog input(s) response timeLI1...LI6 8 ms, tolerance +/- 0.7 ms for logic output(s)R1A, R1B, R1C 2 ms for relay output(s)R2A, R2C 2 ms for relay output(s) accuracy+/- 0.2 % (AI1, AI2, AI3) for a temperature of -10...60 °C+/- 0.5 % (AI1, AI2, AI3) for a temperature of 25 °C+/- 1 % (AO1) for a temperature of 25 °C+/- 2 % (AO1) for a temperature of -10...60 °C linearity error+/- 0.2...0.5 % of maximum value (AI1, AI2, AI3)+/- 0.3 % (AO1) analogue output number1 analogue output typeAO1 software-configurable current 0...20 mA, impedance: 800 Ohm, resolution 10 bitsAO1 software-configurable voltage 0...10 V, impedance: 470 Ohm, resolution 10 bits discrete output number3 discrete output typeConfigurable relay logic: (R1A, R1B, R1C) NO/NC - 100000 cyclesConfigurable relay logic: (R2A, R2B) NO - 100000 cyclesLogic: (LO) minimum switching current5 mA at 24 V DC for configurable relay logic maximum switching currentR1: 3 A at 250 V AC resistive load, cos phi = 1R1: 4 A at 30 V DC resistive load, cos phi = 1R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4R2: 5 A at 250 V AC resistive load, cos phi = 1R2: 5 A at 30 V DC resistive load, cos phi = 1 discrete input number7 discrete input typeProgrammable (sink/source) (LI1...LI4)24...30 V DC, with level 1 PLCProgrammable as pulse input 20 kpps (LI5)24...30 V DC, with level 1 PLCSwitch-configurable PTC probe (LI6)24...30 V DCSafe torque off (STO)24...30 V DC - 1500 Ohm discrete input logicNegative logic (sink) (LI1...LI6), > 19 V (state 0), < 13 V (state 1)Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1) acceleration and deceleration rampsURamp switchingDeceleration ramp automatic stop DC injectionDeceleration ramp adaptationLinearCUSS braking to standstillBy DC injection protection typeInput phase breaks: driveOvercurrent between output phases and earth: driveOverheating protection: driveShort-circuit between motor phases: driveThermal protection: drive communication port protocolCANopenModbus connector type1 RJ45 (on front face) for Modbus/CANopen physical interface2-wire RS 485 for Modbus transmission frameRTU for Modbus type of polarizationNo impedance for Modbus number of addresses1…127 for CANopen1…247 for Modbus method of accessSlave CANopen electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test, level 3 conforming to IEC 61000-4-5Conducted radio-frequency immunity test, level 3 conforming to IEC 61000-4-6Electrical fast transient/burst immunity test, level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test, level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test, level 3 conforming to IEC 61000-4-3Voltage dips and interruptions immunity test conforming to IEC 61000-4-11 width60 mm height325 mm depth245 mm net weight2.9 kg option cardCommunication card for CANopen daisy chainCommunication card for CANopen open styleCommunication card for DeviceNetCommunication card for Ethernet/IPCommunication card for Profibus DP V1 Environment standardsEN 61800-3 environments 1 category C2EN 55011 class A group 1EN/IEC 61800-5-1EN/IEC 61800-3EN 61800-3 environments 2 category C2 product certificationsGOSTCSAC-TickNOM 117UL markingCE pollution degree2 conforming to EN/IEC 61800-5-1 IP degree of protectionIP20 conforming to EN/IEC 61800-5-1 vibration resistance1 gn (f = 13…200 Hz) conforming to EN/IEC 60068-2-61.5 mm peak to peak (f = 3…13 Hz) conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5…95 % without condensation conforming to IEC 60068-2-35…95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for operation-10…50 °C without50…60 °C with derating factor ambient air temperature for storage-25…70 °C operating altitude<= 1000 m without1000...2000 m with current derating 1 % per 100 m operating positionVertical +/- 10 degree
User guideSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsInstruction sheetSizeAdd to My Documents
Software and FirmwareLanguage
EDS filesSizeAdd to My Documents
Technical FAQsNo results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.