variable speed drive ATV312 - 0.18kW - 0.6kVA - 24W - 200..240 V- 1-phase supplyShow more characteristics >
Add to My Products Remove from My Products
The maximum number of products that can be compared is 4
Main range of productAltivar 312 Solar product or component typeVariable speed drive product destinationAsynchronous motors product specific applicationPumping station with photovoltaic arrays assembly styleWith heat sink device short nameATV312 Complementary motor power kW0.18 kW motor power hp0.25 hp [Us] rated supply voltage200...240 V (- 5...5 %) supply voltage limits170...264 V supply frequency50...60 Hz (- 5...5 %) network frequency47.5...63 Hz network number of phasesSingle phase line current3 A at 200 V, Isc = 1 kA2.5 A at 240 V EMC filterIntegrated apparent power0.6 kVA prospective line Isc1 kA continuous output current1.5 A at 4 kHz maximum transient current2.3 A for 60 s power dissipation in W24 W at nominal load speed drive output frequency0.5...500 Hz nominal switching frequency4 kHz switching frequency2...16 kHz (adjustable) speed range1...50 transient overtorque150...170 % of nominal motor torque braking torque<= 150 % with braking resistor for 60 s100 % with braking resistor continuously150 % without braking resistor asynchronous motor control profileFactory set: energy saving mode regulation loopFrequency PI regulator motor slip compensationSuppressableAdjustableAutomatic whatever the load output voltage<= power supply voltage electrical connectionTerminal - cable cross section: 2.5 mm², AWG 14 (terminal(s) Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6)Terminal - cable cross section: 2.5 mm², AWG 14 (terminal(s) L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-) tightening torque0.6 N.m (terminal(s) Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6)0.8 N.m (terminal(s) L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-) insulationElectrical between power and control supplyInternal supply for logic inputs at 19...30 V, <= 100 A, protection type: overload and short-circuit protectionInternal supply for reference potentiometer (2.2 to 10 kOhm) at 10...10.8 V, <= 10 A, protection type: overload and short-circuit protection analogue input number3 analogue input typeAI1 configurable voltage 0...10 V, 30 V max, impedance: 30000 OhmAI2 configurable voltage +/- 10 V, 30 V max, impedance: 30000 OhmAI3 configurable current 0...20 mA, impedance: 250 Ohm sampling duration8 ms (terminal(s) AI1, AI2, AI3), input: analog4 ms (terminal(s) LI1...LI6), input: discrete response time8 ms, output: analog (terminal(s) AOV, AOC)8 ms, output: discrete (terminal(s) R1A, R1B, R1C, R2A, R2B) linearity error+/- 0.2 % output analogue output number2 analogue output typeAOC configurable current 0...20 mA, impedance: 800 Ohm, resolution: 8 bitsAOV configurable voltage 0...10 V, impedance: 470 Ohm, resolution: 8 bits discrete input logicLI1...LI4 logic input not wired, < 13 V (state 1)LI1...LI6 negative logic (source), > 19 V (state 0)LI1...LI6 positive logic (source), < 5 V (state 0), > 11 V (state 1) discrete output number2 discrete output typeR1A, R1B, R1C configurable relay logic, 1 NO + 1 NC, electrical service life: 100000 cyclesR2A, R2B configurable relay logic, NC, electrical service life: 100000 cycles minimum switching current10 mA at 5 V DC (terminal(s) R1-R2) maximum switching current2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1-R2)2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (R1-R2)5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (R1-R2)5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (R1-R2) discrete input number6 discrete input typeLI1...LI6 programmable at 24 V, 0...100 mA for PLC, impedance: 3500 Ohm acceleration and deceleration rampsLinear adjustable separately from 0.1 to 999.9 sS, U or customized braking to standstillBy DC injection protection typeLine supply overvoltage and undervoltage safety circuits for driveLine supply phase loss safety function, for three phases supply for driveMotor phase breaks for driveOvercurrent between output phases and earth (on power up only) for driveOverheating protection for driveShort-circuit between motor phases for driveThermal protection for motorInput phase breaks for drive dielectric strength2040 V DC between earth and power terminals2880 V AC between control and power terminals insulation resistance>= 500 mOhm at 500 V DC for 1 minute local signalling1 LED (red) signal for drive voltageFour 7-segment display units signal for CANopen bus status time constant5 ms for reference change frequency resolution0.1...100 Hz for analog input0.1 Hz for display unit communication port protocolModbusCANopen connector type1 RJ45 for Modbus/CANopen physical interfaceRS485 multidrop serial link transmission frameRTU transmission rate10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen4800, 9600 or 19200 bps for Modbus number of addresses1...247 for Modbus1...127 for CANopen number of drive127 for CANopen31 for Modbus electromagnetic compatibility1.2/50 µs - 8/20 µs surge immunity test - test level 3 conforming to IEC 61000-4-5Electrical fast transient/burst immunity test - test level 4 conforming to IEC 61000-4-4Electrostatic discharge immunity test - test level 3 conforming to IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test - test level 3 conforming to IEC 61000-4-3 standardsIEC 61800-5-1 markingCE height145 mm width72 mm depth132 mm product weight1.5 kg option cardCommunication card for CANopen daisy chainCommunication card for Profibus DPCommunication card for Modbus TCPCommunication card for FipioCommunication card for DeviceNet Environment IP degree of protectionIP20 without cover plate pollution degree2 protective treatmentTC vibration resistance1.5 mm (f = 3...13 Hz) conforming to EN/IEC 60068-2-61 gn (f = 13...150 Hz) conforming to EN/IEC 60068-2-6 shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27 relative humidity5...95 % without condensation conforming to IEC 60068-2-35...95 % without dripping water conforming to IEC 60068-2-3 ambient air temperature for storage-25...70 °C ambient air temperature for operation-10...50 °C without derating with protective cover on top of the drive-10...60 °C with derating factor without protective cover on top of the drive operating altitude<= 1000 m without derating>= 1000 m with current derating 1 % per 100 m operating positionVertical +/- 10 degree Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.