Main range of productAltivar 212 product or component typeVariable speed drive device short nameATV212 product destinationAsynchronous motors product specific applicationPumps and fans in HVAC assembly styleWith heat sink network number of phases3 phases motor power kW30 kW motor power hp40 hp [Us] rated supply voltage380...480 V - 15...10 % supply voltage limits323...528 V supply frequency50...60 Hz - 5...5 % network frequency47.5...63 Hz EMC filterClass C2 EMC filter integrated line current44.7 A 480 V56.7 A 380 V Complementary apparent power44.6 kVA 380 V prospective line Isc22 kA continuous output current58.5 A 380 V58.5 A 460 V maximum transient current64.4 A 60 s speed drive output frequency0.5...200 Hz nominal switching frequency8 kHz switching frequency6...16 kHz adjustable8...16 kHz with derating factor speed range1...10 speed accuracy+/- 10 % of nominal slip 0.2 Tn to Tn torque accuracy+/- 15 % transient overtorque120 % of nominal motor torque +/- 10 % 60 s asynchronous motor control profileFlux vector control without sensor, standardVoltage/frequency ratio, 5 pointsVoltage/frequency ratio - Energy Saving, quadratic U/fVoltage/frequency ratio, 2 pointsVoltage/frequency ratio, automatic IR compensation (U/f + automatic Uo) regulation loopAdjustable PI regulator motor slip compensationAutomatic whatever the loadNot available in voltage/frequency ratio motor controlAdjustable local signalling1 LED red DC bus energized output voltage<= power supply voltage isolationElectrical between power and control type of cableIEC cable without mounting kit 1 45 °C copper 90 °C XLPE/EPRIEC cable without mounting kit 1 45 °C copper 70 °C PVCUL 508 cable with UL Type 1 kit 3 40 °C copper 75 °C PVC electrical connectionTerminal 2.5 mm² AWG 14 VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RESTerminal 50 mm² AWG 1/0 L1/R, L2/S, L3/T tightening torque24 N.m 212 lb.in L1/R, L2/S, L3/T0.6 N.m VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES supplyInternal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 % <= 10 A overload and short-circuit protectionInternal supply 24 V DC 21...27 V <= 200 A overload and short-circuit protection analogue input number2 analogue input typeSwitch-configurable voltage VIA 0...10 V DC 24 V max 30000 Ohm 10 bitsConfigurable voltage VIB 0...10 V DC 24 V max 30000 Ohm 10 bitsConfigurable PTC probe VIB 0...6 probes 1500 OhmSwitch-configurable current VIA 0...20 mA 250 Ohm 10 bits sampling duration2 ms +/- 0.5 ms F discrete2 ms +/- 0.5 ms R discrete2 ms +/- 0.5 ms RES discrete3.5 ms +/- 0.5 ms VIA analog22 ms +/- 0.5 ms VIB analog response time2 ms +/- 0.5 ms FM analog7 ms +/- 0.5 ms FLA, FLC discrete7 ms +/- 0.5 ms FLB, FLC discrete7 ms +/- 0.5 ms RY, RC discrete accuracy+/- 0.6 % VIA for a temperature variation 60 °C+/- 0.6 % VIB for a temperature variation 60 °C+/- 1 % FM for a temperature variation 60 °C linearity error+/- 0.15 % of maximum value input VIA+/- 0.15 % of maximum value input VIB+/- 0.2 % output FM analogue output number1 analogue output typeSwitch-configurable voltage FM 0...10 V DC 7620 Ohm 10 bitsSwitch-configurable current FM 0...20 mA 970 Ohm 10 bits discrete output number2 discrete output typeConfigurable relay logic FLA, FLC NO 100000 cyclesConfigurable relay logic FLB, FLC NC 100000 cyclesConfigurable relay logic RY, RC NO 100000 cycles minimum switching current3 mA 24 V DC configurable relay logic maximum switching current5 A 250 V AC resistive cos phi = 1 L/R = 0 ms FL, R5 A 30 V DC resistive cos phi = 1 L/R = 0 ms FL, R2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms FL, R2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms FL, R discrete input typeProgrammable F 24 V DC level 1 PLC 4700 OhmProgrammable R 24 V DC level 1 PLC 4700 OhmProgrammable RES 24 V DC level 1 PLC 4700 Ohm discrete input logicPositive logic (source) F, R, RES <= 5 V >= 11 VNegative logic (sink) F, R, RES >= 16 V <= 10 V acceleration and deceleration rampsAutomatic based on the loadLinear adjustable separately from 0.01 to 3200 s braking to standstillBy DC injection protection typeMotor phase break motorBreak on the control circuit driveThermal power stage driveOvervoltages on the DC bus driveAgainst exceeding limit speed driveAgainst input phase loss driveWith PTC probes motorInput phase breaks driveLine supply overvoltage and undervoltage driveLine supply undervoltage driveOvercurrent between output phases and earth driveOverheating protection driveShort-circuit between motor phases driveThermal protection motor dielectric strength3535 V DC between earth and power terminals5092 V DC between control and power terminals insulation resistance>= 1 MOhm 500 V DC for 1 minute frequency resolution0.024/50 Hz analog input0.1 Hz display unit communication port protocolMETASYS N2ModbusAPOGEE FLNLonWorksBACnet connector type1 RJ451 open style physical interface2-wire RS 485 transmission frameRTU transmission rate9600 bps or 19200 bps data format8 bits, 1 stop, odd even or no configurable parity type of polarizationNo impedance number of addresses1...247 communication serviceWrite multiple registers (16) 2 words maximumTime out setting from 0.1 to 100 sMonitoring inhibitableRead device identification (43)Write single register (06)Read holding registers (03) 2 words maximum option cardCommunication card LonWorks operating positionVertical +/- 10 degree width240 mm height420 mm depth214 mm product weight26.4 kg power dissipation in W847 W air flow290 m3/h functionalityMid specific applicationHVAC IP degree of protectionIP21 Variable speed drive application selectionBuilding - HVAC : compressor for scrollBuilding - HVAC : fanBuilding - HVAC : pump Motor power range AC-330...50 kW at 380...440 V 3 phases30...50 kW at 480...500 V 3 phases motor starter typeVariable speed drive Environment electromagnetic compatibilityConducted radio-frequency immunity test level 3 IEC 61000-4-6Voltage dips and interruptions immunity test IEC 61000-4-111.2/50 µs - 8/20 µs surge immunity test level 3 IEC 61000-4-5Electrical fast transient/burst immunity test level 4 IEC 61000-4-4Electrostatic discharge immunity test level 3 IEC 61000-4-2Radiated radio-frequency electromagnetic field immunity test level 3 IEC 61000-4-3 pollution degree3 IEC 61800-5-1 IP degree of protectionIP20 on upper part without blanking plate on cover EN/IEC 61800-5-1IP20 on upper part without blanking plate on cover EN/IEC 60529IP21 EN/IEC 61800-5-1IP21 EN/IEC 60529IP41 on upper part EN/IEC 61800-5-1IP41 on upper part EN/IEC 60529 vibration resistance1 gn 13...200 Hz EN/IEC 60068-2-81.5 mm 3...13 Hz EN/IEC 60068-2-6 shock resistance15 gn 11 ms IEC 60068-2-27 environmental characteristicClasses 3C1 IEC 60721-3-3Classes 3S2 IEC 60721-3-3 noise level59.9 dB 86/188/EEC operating altitude1000...3000 m limited to 2000 m for the Corner Grounded distribution network with current derating 1 % per 100 m<= 1000 m without derating relative humidity5...95 % without condensation IEC 60068-2-35...95 % without dripping water IEC 60068-2-3 ambient air temperature for operation-10...40 °C without derating> 40...50 °C with derating factor ambient air temperature for storage-25...70 °C standardsEN 61800-3EN 61800-3 environments 1 category C2UL Type 1EN 61800-3 environments 1 category C1EN 61800-3 environments 1 category C3EN 61800-3 environments 2 category C1IEC 61800-3 environments 1 category C2IEC 61800-3 environments 2 category C3EN 55011 class A group 1IEC 61800-3EN 61800-3 environments 2 category C3IEC 61800-3 category C3IEC 61800-3 environments 1 category C1EN 61800-5-1IEC 61800-5-1EN 61800-3 category C3IEC 61800-3 environments 2 category C2EN 61800-3 category C2IEC 61800-3 environments 1 category C3IEC 61800-3 environments 2 category C1IEC 61800-3 category C2EN 61800-3 environments 2 category C2 product certificationsULCSAC-TickNOM 117 markingCE Offer Sustainability Sustainable offer statusGreen Premium product RoHS (date code: YYWW) REACh Product environmental profile Product end of life instructionsAvailable Contractual warranty Warranty period18 months
Documents and DownloadsLanguage
DTM filesSizeAdd to My DocumentsCatalogueSizeAdd to My DocumentsUser guideSizeAdd to My DocumentsCADSizeAdd to My DocumentsCertificateSizeAdd to My DocumentsInstruction sheetSizeAdd to My DocumentsProduct Environmental ProfileSizeAdd to My Documents
No results found.Unfortunately, related FAQs are unavailable due to temporary technical issues. Please try again later.
Dimensions in mm
Dimensions in in.
EMC mounting plate (supplied with drive)
Dimensions in mm
Dimensions in in.
Mounting and ClearanceMounting RecommendationsClearance
Depending on the conditions in which the drive is to be used, its installation will require certain precautions and the use of appropriate accessories.
Install the unit vertically:
Do not place it close to heating elements.
Leave sufficient free space to ensure that the air required for cooling purposes can circulate from bottom to the top of the unit.
Type A mounting
Type B mounting
Type C mounting
By removing the protective blanking cover from the top of the drive, the degree of protection for the drive becomes IP21. The protective blanking cover may vary according to the drive model, see opposite.Specific Recommendations for Mounting in an Enclosure
To help ensure proper air circulation in the drive:
Sealed Metal Enclosure (IP54 Degree of Protection)
Fit ventilation grilles.
Check that there is sufficient ventilation. If there is not, install a forced ventilation unit with a filter. The openings and/or fans must provide a flow rate at least equal to that of the drive fans (refer to the product characteristics).
Use special filters with UL Type 12/IP54 protection.
Remove the blanking cover from the top of the drive.
The drive must be mounted in a dust and damp proof enclosure in certain environmental conditions, such as dust, corrosive gases, high humidity with risk of condensation and dripping water, splashing liquid, etc.This enables the drive to be used in an enclosure where the maximum internal temperature reaches 50°C.
Connections and SchemaRecommended Wiring Diagram3-Phase Power SupplyA1:ATV 212 driveKM1:ContactorQ1:Circuit breakerQ2:GV2 L rated at twice the nominal primary current of T1Q3:GB2CB05S1, S2:XB4 B or XB5 A pushbuttonsT1:100 VA transformer 220 V secondary(1)Fault relay contacts for remote signalling of the drive status(2)Connection of the common for the logic inputs depends on the positioning of the switch (Source, PLC, Sink)(3)Reference potentiometer SZ1RV1202
NOTE: All terminals are located at the bottom of the drive. Install interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Switches (Factory Settings)
Voltage/current selection for analog I/O (VIA and VIB)
Voltage/current selection for analog I/O (FM)
Selection of logic type(1)negative logic(2)positive logicOther Possible Wiring DiagramsLogic Inputs According to the Position of the Logic Type Switch
“PLC” position with PLC transistor outputs(1)PLC(1)PLC
2-wire controlF:ForwardR:Preset speed(2)ATV 212 control terminals
3-wire controlF:ForwardR:StopRES:Reverse(2)ATV 212 control terminals
PTC probe(2)ATV 212 control terminals(3)MotorAnalog Inputs
Voltage analog inputs
External +10 V(2)ATV 212 control terminals(4)Speed reference potentiometer 2.2 to 10 kΩ(2)ATV 212 control terminals
Analog input configured for current: 0-20 mA, 4-20 mA, X-Y mA(2)ATV 212 control terminals(5)Source 0-20 mA, 4-20 mA, X-Y mA
Analog input VIA configured as positive logic input (“Source” position)(2)ATV 212 control terminals
Analog input VIA configured as negative logic input (“Sink” position)(2)ATV 212 control terminals
Performance CurvesDerating Curves
The derating curves for the drive nominal current (In) depend on the temperature, the switching frequency and the mounting type (A, B or C).
For intermediate temperatures (45°C for example), interpolate between 2 curves.XSwitching frequency